2002 Dodge Dakota 4.7 Crankshaft Position Sensor Location

By Ra_Azaria190 23 Apr, 2022 Post a Comment

The cam sensor on the 47 is located toward the forward edge of the right cylinder head passenger side. Brake Booster Replacement 422 - 462 in San Luis Obispo CA.

Crankshaft Position Sensor Replacement Bought A New Non Mopar

I reached it from underneath the car.

. This has a 3 wire connector tanwith yellow tracer is sensor signal black light blue tracer wire is sensor ground and the orange is the 5V supply. Asked by flynndo in Potwin KS on. 2002 Dodge Dakota Base 6 Cyl 39L Standard Transmission.

Where is the camshaft sensor located on 2002 Dodge Dakota. Car Service Estimate ShopDealer Price. Symptoms was driving engine quit Tach indicator with engine stopped was jumping 0-5000 RPM.

The camshaft sensor pigtail comes through the front of the distributor and connects to the engine wiring harness above the intake manifold. 06222013 Vehicle starts to misfire at any rpm will not startI am a certified techcoil newcrank sensor newvoltage reading at coil 10. Could ship from same location as parts in cart.

Prices may vary depending on your location. No parts for vehicles in selected markets. Crankshaft Position Sensor Connector.

2009 Dodge Dakota V6-37L. Youll need to connect your multimeter test lead to a back probe or a wire. The camshaft position sensor is located inside the distributor.

The crankshaft pulley is the large pulley located in the center lower portion of the front of the. 47 cam position sensor. Joined Jul 7 2008 1 Posts.

49v on pcm side good bright pulse and consistent. DODGE 2004 DAKOTA 47L V8 Ignition Crankshaft Position Sensor. 2002 Dodge Dakota Estimates.

Jump to Latest Follow. The sensor were testing is the crankshaft position sensor thats bolted to the transmission bell housing. Could ship from same location as parts in cart.

Camshaft position sensor CMP located at the front of pass side cylinder head Crankshaft position sensor CKP located at the pass side rear of engine by the transmission Engine coolant temperature sensor ECT located at the front of engine. Accessing the sensor requires removing the distributor cap and the distributor rotor. 00007 2001 47L Dodge Dakota Code P0340 Crankshaft P1391 Camshaft position Sensor.

CRANKSHAFT POSITION SENSOR - 47L V-8 ENGINEREMOVALThe Crankshaft Position CKP sensor is located at the right-rear side of the engine cylinder block CKP Sensor LocationRemoval. They changed the crank sensor engine ran 30 minutes and quit same code. Discussion Starter 1 Jul 7 2008.

1 Crankshaft Position Sensor problem of the 2002 Dodge Dakota Failure Date. DODGE 2002 DAKOTA 47L V8 Ignition Crankshaft Position Sensor. This has a 3 wire connector tanwith yellow tracer is sensor signal black light blue tracer wire is sensor ground and the orange is the 5V supply.

The crankshaft position sensor must be connected to its engine harness connector for this test to work. 2012 Ram 1500 47L POWERTECHMAGNUM V8. 2002 dodge dakota 47 ltr.

I have my truck in at a Dodge dealer10 days now. 47 Crank POsition Sensor. The Dodge Anti Theft system or The Sentry Key Immobilizer System SKIS is designed to provide passive protection against unauthorized vehicle use by disabling the engine after about two seconds of running whenever any method other than a valid Sentry Key is used to start the vehicle.

Had it towed in scanned was told the code was saying Crank sensor communication was interupted. Crankshaft Position Sensor - 39L59L Engine Manual. Only show this userhelpI have a late 2002 Dodge Ram 1500 47L and I need to replace the crank position sensor but cant seem to locate it.

No parts for vehicles in selected markets. I dont think it has to be removed but its one bolt on the bottom of the head then the sensor can be pulled out. How to find and remove the crankshaft position sensor.

The crankshaft sensor is located just above the the oil filter which is by the front of the engine by the firewall. The camshaft position sensor is located on the distributor for all engines designed for the 1998 Dodge Dakota. Dakota Durango Forum.

Be the first to answer this question. The cam sensor on the 47 is located toward the forward edge of the right cylinder head passenger side. Code 0340 cam shaft sensor.

Anyone tell me where it is and the steps to replace it. Its too easy to do given the other things that need to happen to get to that stage to not do. On average the cost for a Dodge Dakota Crankshaft Position Sensor Replacement is 132 with 37 for parts and 95 for labor.

Camshaft sensor location. View with engine cover installed. The crankshaft position sensor is located at the lower left hand side of the crankshaft pulley.

Power Steering System Leak Inspection.

Camshaft Position Sensor Dodge Stalling Youtube